Home › ATOMSTACK › ATOMSTACK L2 Smart Z-Axis Module Installation Guide

ATOMSTACK L2 Smart Z-Axis Module Giya sa Pag-instalar

ATOMSTACK L2 Smart Z-Axis Module

Z-axis taas nga auto adjuster nga manwal sa pag-instalar L2-5W/L2-10W/L2-20W/L2-40W

Mubo nga sulat: Ang mga imahe alang lamang sa pakisayran, palihug tan-awa ang aktwal nga produkto. Para sa dugang nga impormasyon, palihog i-scan ang QR code.

listahan

Pamaagi sa pag-instalar sa Z axis

A5 PRO V2/A10 PRO V2

I-unscrew ang 4 pcs M4*6 counterclockwise para matangtang ang slider

I-install ang A5 Pro V2/A10 Pro V2 nga gipahinungod nga konektor
Hupti ang 4 pcs M4*6

A20 PRO V2/A40 PRO V2

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral A48 PRO/A48 Ultra dili na kinahanglan nga ibalhin ang limit switch

Lakang 1

I-flip sa ibabaw sa engraver
Kuhaa ang 2 screws off limit switch board
Ibalhin sa unahan ang board aron i-align ang 2 ka buho
I-lock ang 2 ka screw balik sa board
Paghuman
I-flip sa ibabaw sa engraver

Laser unified nga pamaagi sa pag-instalar

Lakang:1 Kuhaa ang 4 pcs M3 ug laser slider
Lakang:2 I-install ang laser slider nga adunay 4 M3 screws nga gikuha sa lakang 1

Mubo nga sulat: Unscrew una ang pag-ayo nga piraso gamit ang cross screwdriver sa toolkit, dayon i-install ang laser slider sa A48 laser

Pamaagi sa koneksyon sa cable

Pamaagi sa pag-instalar sa laser
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral/ A12 Ultral/A24 Ultral/X12 Ultral/ X24 Ultral

A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

Mubo nga sulat: Sa diha nga ang gahum sa paggamit sa Z-axis gitas-on auto adjuster, kamo kinahanglan lamang nga mopadayon sa "auto focus" button sa control box sa auto focus sa laser

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral

Mubo nga sulat: Kinahanglan ang display kung gamiton ang Z-axis height auto adjuster, kinahanglan nimo nga kontrolon kini gikan sa display end

Serbisyo sa kustomer: Alang sa detalyado nga palisiya sa warranty, palihug bisitaha ang among opisyal website : www.atomstack.com Alang sa teknikal nga suporta ug serbisyo, palihug email: support@atomstack.com
Manufacturer: Shenzhen AtomStack Technologies Co.,Ltd
adres: 17th Floor, Building 3A, Phase II, Intelligent Park, No. 76, Baohe Avenue, Bip code: tret, Longgang District, Shenzhen, Guangdong, China
I-scan ang QR code: O code reader/barcode scanner o bisan unsang app nga naay scanner

Mga Dokumento / Mga Kapanguhaan

L2 Smart Z-Axis Module

Installation Guide · L2, L2 Smart Z-Axis Module, Smart Z-Axis Module, Z-Axis Module, Module

Mga pakisayran

Manwal sa Gumagamitmanual.tools

Published: July 13, 2024

Gi-update: Hulyo 14, 2024

Mga pangutana ug tubag

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Mga Pangutana ug Tubag

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

🇺🇸 Robert nag-ingon:

Abril 23, 2026 sa 12:48 sa hapon
I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob
🇺🇸 Robert asks I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob

Manuals+ clarified question

Pangutana

How do I connect the L2 Smart Z-Axis Module cable to an ATOMSTACK A20 PRO V2 machine?
Tubag

Aron makonektar ang ATOMSTACK L2 Smart Z-Axis Module sa imong A20 PRO V2, you must use the specific wiring method outlined in the manual for "V2" series machines. The connection does not plug directly into a spare port on the motherboard; instead, it typically involves an adapter or a specific bridge connection.

Sumala sa Section 05 — Cable connection method for the A20 PRO V2:

X-Axis Connection: The Z-axis module cable usually connects to the transfer board located on the X-axis carriage.

Y-Axis Motor Comparison: While the connector may look similar to a Y-axis motor plug, it is intended for the Z-axis control port. On V2 models, this is often a 4-pin or 6-pin connector located on the breakout board near the laser module mount.

Check for the Adapter: Ensure you are using the "Z-axis connection cable" included in the L2 kit (listed as item 4 in the 01-List). One end connects to the L2 module motor, and the other connects to the reserved Z-axis port on the machine's X-axis terminal.

If the connector physically does not fit any port on the X-axis carriage board, please verify if your kit included a small adapter board o a Y-shaped splitter cable, as some V2 revisions require splitting the signal or using a specific conversion interface provided in the L2 box.
Read the full Q&A page
tubag
1. 🇺🇸 Robert nag-ingon:
  
  Abril 23, 2026 sa 2:31 sa hapon
  I don’t know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don’t see any extra ports anywhere .
  🇺🇸 Robert asks I don't know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don't see any extra ports anywhere .
  
  Manuals+ clarified question
  
  Pangutana
  
  Where are the transfer board and X-axis terminal located on the ATOMSTACK L2 Smart Z-Axis Module?
  
  Tubag
  
  Based on the installation manual for the ATOMSTACK L2 Smart Z-Axis Module, the components you are looking for are part of the cable connection setup (Section 05):
  
  Transfer Board: This is the small PCB (circuit board) located on the back or side of the X-axis carriage (the part that moves left and right). On many AtomStack models like the A6, A12, A24, and X24 series, this board is where the main ribbon cable connects.
  
  X-axis Terminal: This refers to the specific port on that transfer board. For the L2 module, you typically need to plug the Z-axis connection cable into the port labeled for the Z-axis or the auxiliary port on this board.
  
  Mubo nga sulat: If you do not see extra ports, ensure you are looking at the balik of the laser carriage assembly. On some older models (like the A5 Pro or V2 series), the connection method differs and may involve connecting directly to the main control box or using a specific adapter cable included in the L2 kit. Please verify your specific machine model, as the manual shows different wiring paths for the A5/V2 series versus the Pro/Ultra series.
  
  Read the full Q&A page
  tubag
  1. 🇺🇸 Robert nag-ingon:
    
    Abril 23, 2026 sa 2:55 sa hapon
    I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
    
    🇺🇸 Robert asks I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
    
    Manuals+ clarified question
    
    Pangutana
    
    Where are the PCB, extra ports, adapters, or splitters for the ATOMSTACK L2 Smart Z-Axis Module?
    
    Tubag
    
    Based on the ATOMSTACK L2 Smart Z-Axis Module installation guide, the components included in the box (Section 01 - List) are:
    
    Z-axis height adjuster
    
    Laser slider
    
    A5/P/A10/A20/X20/S20 dedicated connector
    
    M3 * 6 nga mga tornilyo
    
    M4 * 5 nga mga tornilyo
    
    Z-axis connection cable
    
    Manwal
    
    2.0/2.5 Allen wrench
    
    Cross screwdriver
    
    Regarding the PCB and Ports: The L2 module is designed to integrate with existing AtomStack frames. For many models (like the A6 Pro, A12 Pro, A24 Pro, etc.), the connection is made directly to the existing X-axis motor interface or the laser module's connection point using the provided Z-axis connection cable. There is typically no separate external PCB board included in this kit.
    
    Regarding Adapters/Splitters: The manual shows that for certain models (Section 05 - Cable connection method), you must unplug the original X-axis motor cable and connect it to the Z-axis module's interface, or use the dedicated connector provided in the kit. If your specific machine model is not listed in the manual (A5, A10, A20, A6 Pro, etc.), you may require a specific adapter not included in the standard L2 package. If these items are missing from your specific kit, it is recommended to contact support@atomstack.com para sa verification.
    
    Read the full Q&A page
    tubag
    1. 🇺🇸 Robert nag-ingon:
      
      Abril 23, 2026 sa 3:23 sa hapon
      
      Now what do I do ?
      
      🇺🇸 Robert asks Now what do I do ?
      
      Manuals+ clarified question
      
      Pangutana
      
      What are the next steps after installing the ATOMSTACK L2 Smart Z-Axis Module?
      
      Tubag
      
      Once you have physically mounted the ATOMSTACK L2 Smart Z-Axis Module and connected the cables as shown in the manual, you must configure your software to recognize the new hardware. Follow these steps:
      
      Pagpamatuod sa Cable: Ensure the Z-axis connection cable is securely plugged into the module and the corresponding port on your laser engraver's motherboard (refer to Section 05 of the manual for your specific model).
      
      Konfigurasyon sa Software: Open your laser control software (LightBurn or LaserGRBL). You may need to enable the Z-axis in the device settings. In LightBurn, go to Mga Setting sa Device and ensure 'Enable Z-Axis' is toggled on.
      
      Pagtutok: The L2 module is designed for automatic or simplified focusing. Use the control panel or software commands to move the Z-axis up and down to verify smooth movement before starting a project.
      
      Limitahan ang mga switch: If you are using models like the A6 Pro, A12 Pro, or A24 Pro, the manual notes that you do not need to relocate the limit switches.
      
      If the module is not moving, double-check that the 2-pin or 4-pin connectors are not reversed and that your machine's firmware is up to date.
      
      >
      
      Read the full Q&A page
      
      tubag

Pangutana Cancel question

May Kalabutan nga mga Hilisgutan

Module L2