ELKO EKO07042 Occupancy Sensor

Deskripsyon sa Produkto

• The EKO07042 is a ceiling flush mount or surface mount occupancy sensor suitable for indoor or outdoor applications.
• It is ideal for use in offices, conference rooms, hotels, homes, etc.
• The sensor allows users to adjust time and Lux values to meet different requirements for switching lights on and off.
• Avoid aiming the sensor towards objects that may sway in the wind or have highly reflective surfaces.
• Avoid mounting the sensor near heat sources.
• The load can be manually switched on using an external push button switch (N.C. 10 A type).
• A short press (1 sec) on the push button switch can switch on the load when it is off, and Lux adjustment is disabled.
• The load will automatically switch off if no movement is detected after the delay time.

TEKNIKAL NGA ESPESPIKASYON

Pahimangno sa Kaluwasan

KUYAW

• KALISOD SA ELECTRIC SHOCK, PAGBUTO O ARC FLASH
• Ang luwas nga pag-instalar sa elektrisidad kinahanglan nga himuon lamang sa mga batid nga propesyonal. Ang mga batid nga propesyonal kinahanglan magpamatuod sa lawom nga kahibalo sa mga musunud nga lugar:
• Pagkonektar sa mga network sa pag-install
• Pagkonektar sa pipila ka mga electrical device
• Pagbutang sa mga kable sa kuryente
• Mga sumbanan sa kaluwasan, mga lagda ug regulasyon sa lokal nga mga kable
• Do not mount the occupancy sensor on a conductive surface, such as metal wallpaper.
• Turn off the power when changing the light sources.
• Only open or repair the unit if you are a qualified electrician.

Ang pagkapakyas sa pagsunod niini nga mga panudlo moresulta sa kamatayon o grabe nga kadaot.

NOTA

• Make sure to always wire the sensor according to the wiring diagram. Don’t mix up L (load) or L (live supply) with N. Wrong connections will result in damage to the device.
• High in-rush current can occur if certain bulb brands are used and may cause permanent damage the unit.

MGA SULOD NGA PACKAGE

DESKRIPSIYON SA PRODUKTO

Mga bahin

• EKO07042 is a ceiling flush mount or surface mount occupancy sensor both applicable for indoor or outdoor application which is ideal for use in office, conference room, hotel, home, etc.
• With its Knobs, the time and Lux value can be adjusted as user desires to match different requirements for switching light on and off.
• High-performance relay for connecting all types of lights, e.g. compensated / uncompensated fluorescent lamp, halogen lamp, incandescent lamp,etc.
• Flexible and wide mounting methods: Flush mount with spring clip or European standard junction box, surface mount with junction box is also available.
• High sensitivity is provided by a unique lens with “no dead spot” zones in its 360° high intensity of detection.
• A built-in red LED is used as an indicator for easy test operation and different operation modes clear identification.
• Manually switch on the loads by wire connected to an external N.C. type push button switch when the ambient light level exceeds the pre-set Lux value.

Dimensyon

• EKO07042: Φ111.5 x 59 mm (See FIG. 1 -A)

• Junction Box: Φ111.5 x 35 mm (See FIG. 1-B)

• Sensor unit: Φ111.5 x 70 mm (See FIG.1-C)

PAG-INSTALL UG WIRING

Tukma nga Lokasyon

1. It is recommended to install at a height of 2.5 m to gain the optimal detection pattern. The detection range can reach up to 7 m diameter with a 360° detection angle (See FIG.2).
2. Pay attention to the walking direction during the test. EKO07042 is more sensitive to movement across the sensor and less sensitive to movement directly towards to sensor which will reduce the detection coverage (See FIG.3).
   Mas sensitibo sa paglihok tabok sa pattern
   Dili kaayo sensitibo sa paglihok direkta ngadto sa sensor
3. Makatabang nga mga tip sa pag-instalar

Since the sensor is responding to temperature change, please avoid the following conditions (See FIG.4-A & FIG.4-B).

• The sensor is aimed toward objects which may be swayed in the wind, such as curtains, tall plants, miniature gardens, etc.
• Mas sensitibo sa paglihok tabok sa pattern
• Dili kaayo sensitibo sa paglihok direkta ngadto sa sensor
• The sensor is aimed toward the objects whose surfaces are highly reflective, such as mirrors, monitors, etc.
• Mounting the sensor near heat sources, such as heating vents, air conditioning, vents as dryers, lights, etc.

Mga kable

Push button function

1. The load can be manually switched on by using an external push button switch (N.C. 10 A type, See FIG.5 – FIG.6).
   When the load is off, it can be switched on by a short press ( 1sec) on the push button switch and Lux is disabled. After the load is switched on manually, the load can be automatically switched off if no movement is detected and the delay time has expired.
2. EKO07042 for standard application (See FIG.5).
3. One load is controlled by two sensors to enlarge the detection area (See FIG.6).
4. Staircase timer switch control (Timer should be set to, See FIG.7).

Pamaagi sa Pag-instalar

Flush mount

NOTA

• When the sensor is flush-mounted with a spring clip, a protection cap of terminals must be used.
• To install the sensor, please drill a hole with a diameter of 65 mm on ceiling board and keep the power cable outside. Please strip off 6 – 8 mm of cable sheathing for wiring (See FIG.8).

• Refer to wiring diagrams for correct cable connections (FIG.5 – FIG.7), then put the protection cap back and screw it tightly (See FIG.9).

• Knock-outs on the protection cap of terminals are for cable entry.
• Please refer to fthe following illustration for the application.
• No knock-outs are used: 2 mm (See FIG.10-A);

• Small knock-outs are used: Φ8mm (See FIG.10-B);

 

• Big knock-outs are used: Φ12.5 mm (See FIG.10-C);

• Close up the sensor’s two spring clips and insert the sensor into the drilled hole on the ceiling (See FIG.11).

Ibalik ang suplay sa kuryente

• Flush mount gamit ang European standard junction box

NOTA

The protection cap of terminals and spring clip are not needed to be used when the sensor is flush mounted with a European standard junction box.

• Take off the sensor’s two spring clips with the tool before installation.

• Pull out cables from the European standard junction box (See FIG.13), then strip off 6 – 8 mm of cable sheathing for wiring (See FIG.5 – FIG.7).

• Turn the decorative frame of the sensor anti-clockwise with proper strength, then insert two screws into the knock-outs on top cover and screw the sensor on the European standard junction box (See FIG.14).

• Cover up the decorative frame and restore the power supply.

Pag-mount sa ibabaw

NOTA

• The protection cap of terminals and spring clip are not needed to be used when the sensor is surface mounted.
• There are 7 pairs of knock-outs with various distances from 41 mm to 85 mm on the bottom cover of the combined junction box. Off-step, these pairs of knock-outs can be selected for different mounting applications (See FIG.15-A). Select the two same figures (41, 53, 60,,,) on both sides (A and B).

• To feed cables through the side of the junction box, please use the cutting pliers to break the cable entry knock-outs on the side of the junction box, then insert cables into the junction box and feed through it. Strip off 6 – 8 mm of cable sheathing for wiring (See FIG.16).

• Choose proper knock-outs to fix the junction box on the surface of ceiling board with two wood screws attached with rubber washer (See FIG.17).

• Take off the sensor’s two spring clips (See FIG. 12), turn the decorative frame of sensor counterclockwise with proper strength, then insert the 4 non-dropping screw to the corresponding screw holes on sensor’s front cover. Afterwards, those 4 screws will not drop off to provide convenience to the subsequent installations (See FIG.18).

• Refer to wiring diagrams for correct wiring connection See FIG.5 – FIG.7).
• Adunay usa ka " ” symbol on the side of the surface of the junction box, the housing of EKO07042 and the decorative frame, respectively for position verification convenience. Keep the “ ” symbol on the junction box and sensor’s front cover in line to assemble them with the attached 4 non-dropping screws, then cover up the sensor’s decorative frame (See FIG.19) and turn it to be tight.

OPERASYON

Lux, Time knob

• Follow the marked values to adjust Lux & Time knobs according to user’s requirement (See FIG.20).

Lux knob setting

• Lux value is adjustable from approx. 10 Lux to 2000 Lux.
• Set Lux knob to 10 Lux, sensor can work at dark status only.
• Set Lux knob to 2000 Lux, sensor can be triggered almost at any light level.

Time knob setting

• Time: Adjustable from 5 secs to 30 mins.
• Test: walk test operation (2 secs on / 2 secs off).
• : Short impulse for staircase timer switch control (1 sec on, 9 secs off).

Test mode (Uncontrolled by Lux)

LED function & reaction

• The red LED of EKO07042 is behind the lens (See FIG.21) for test mode indication.
• In walk test, LED will turn on for 2 secs once the sensor is triggered.
• If sensor is continuously triggered, the red LED will require an interval time of 2 secs to turn on again.
• With the above said LED function, the load doesn’t need to be connected while conducting walk test.
• 2 LED functions is an indicator only in warming up period and test mode.

Pagsulay sa paglakaw

• The purpose of conducting walk test is to check and adjust detection coverage. Set Time knob to “Test”, then conduct a walk test. Lux control is disabled during the walk test.

NOTA

• It takes approx. 60 secs for sensor to warm up after power is supplied for the first time or re-supplied after shut off, then enters into normal operation mode to carry out a walk test.

Pamaagi sa pagsulay

1. Tester must be within the sensor coverage.
2. Pagbalhin sa gahum.
3. Sensor takes approx. 60 secs to warm up with load and LED on, then turn off after warm-up time.
4. Walk from outside across to the detection pattern until LED turns on for approx. 2 secs indicating the movement has been detected (See FIG.22).
5. Repeat step 4 to conduct walk test until the detection pattern meets user’s demands.

Paggamit sa Lens Shield

EKO07042 has provided 2 lens shields for masking the undesired detection area. Each lens shield has 2 layers, each layer includes 6 small shield pieces, and each small piece shield can cover 30° detection area. For example, to install the sensor at a height of 2.5 m, the detection range can reach up to 1 m diameter if the complete lens shield has been used; and up to 3m diameter if only the A layer of lens shield has been used (See FIG.23-A / B).

• After the user chooses the desired detection area, the redundant lens shield should be eliminated.
• Fixing lens shield: There is a circular groove on the back of the decorative frame and the lens shield is designed with a circular hook. The lens shield can be fitted by inserting the hook of lens shield into its corresponding groove on the decorative frame (See FIG.24 & FIG.25).

PAG-USABOT

• When EKO07042 works abnormally, please check the assumptive problems and suggested solutions in the following table that will hopefully to solve your problems.

Problema	Posible nga hinungdan	Gisugyot nga solusyon
Lighting device does not turn on	1.  Power does not turn on. 2.  Wired incorrectly. 3. The ambient light level is too high. 4. Malfunctioned load.	1.  Switch on the power. 2.  Refer to wiring diagrams (FIG.5 – FIG.7) and check if the load is malfunctioning. 3. Set Lux value above the ambient light level, then trigger the sensor and check if the load is switched on or not. 4. Replace the disabled load with a new one.

Problema	Posible nga hinungdan	Gisugyot nga solusyon
Lighting device does not turn off	1. Auto off time is set too long. 2. Sensor is nuisance-triggered. 3. Wired incorrectly.	1. Set auto off time to a shorter time and check the load is switched off or not according to the preset off time. 2. Keep away from detection coverage to avoid activating the sensor while doing the test. 3. Make sure load and wires are connected correctly.
LED does not  turn on	1. Time knob is not set to “Test”. 2. No power supplied. 3. Wired incorrectly.	1. Set Time knob to “Test”, LED acts as an indicator only in warming up period and test mode. 2. Switch on the power. 3. Refer to wiring diagrams (FIG.5 – FIG.7).
Pag-trigger sa kasamok	There are heat sources, highly reflective objects or any objects that may be swayed in the wind within the detection coverage.	Avoid aiming the sensor toward any heat sources, such as air conditioners, electric fans, heaters or any highly reflective surfaces. Make sure there are no swaying objects within the detection coverage.

NOTA

The following conditions may cause lower sensitivity:

• In very foggy days, the sensitivity may be less due to moisture collecting on the lens.
• In very hot days, the sensitivity may be less since high ambient temperature is close to body temperature.
• In very cold days when heavy clothing is worn, especially the facial area is covered, very little heat will be emitted from the body, causing the unit to be less sensitive.

Paglimpyo: Wipe with a dry cloth only. Soap or rough cloth may damage the sensor lens.

KONTAK

• Ang Schneider Electric Industries SAS
• 35 rue Joseph Monier | FR-92500 Rueil-Malmaison elko.no/contact

FAQ

Q: What should I do if there is high inrush current with certain bulb brands?

A: High in-rush current can occur with certain bulb brands and may cause permanent damage to the unit. It is recommended to avoid using bulbs that cause high inrush current to prevent damage.

Mga Dokumento / Mga Kapanguhaan

ELKO EKO07042 Occupancy Sensor [pdf] Manwal sa Gumagamit EKO07042, MS18535, EKO07042 Occupancy Sensor, EKO07042, Occupancy Sensor, Sensor

Mga pakisayran

• Manwal sa Gumagamit